• A Quick Guide To Reef Tank Photography

    Reef Tank Photography : The First Try

    Perhaps I should begin this article by admitting that I'm not a reef addict. I used to have a heavily planted freshwater tank, but I do not (and never have) had a reef tank of my own. If I had a marine tank, there is no question that it would be a reef tank, and they are endlessly fascinating to me... but I don't have one. So, when I call something an anemone that is (to all of you) quite obviously a large polyp coral, feel free to point and laugh, but don't take any more enjoyment out of it than you would if you were to smack-down your neighborhood 3rd grader playing basketball. And with that said...

    In December of 2009, I met a man here in the Seattle area who was leaving his job at Microsoft and moving to Dubai. For years he had cultivated a reef tank, but as much as he loved it, he could not take it with him, and his attempts to photograph it on his own were disappointing. He asked me to photograph the tank so that he'd have something to remember it by until he had a chance to set up a new one, if that time ever came. Now, I've played around with cameras since I was a kid... and began formal study of photography in college many years ago. I've also taken a few snapshots in marine tanks, in addition to quite a bit of macro photography in general, so I didn't anticipate too many problems.

    So, I packed up my macro lens (a Nikon 105mm micro) and a fast 50mm f1.4, and went to start shooting. But I did encounter some problems, and with some time to reflect on them a bit, I've been able to learn from them and develop a tentative guide to help others avoid them. If you're planning on shooting in a reef tank, perhaps you'll find these tips useful, and if you've already had some success, perhaps you'll reply and share your thoughts.

    General Tips
    These were the general thoughts that I had in mind going into the shoot. Most of them will seem pretty basic, but if you don't have experience with reef tanks or photography, they may help.

    1. Set the White Balance: This is especially important if you have to shoot .jpg! There is rarely anything in a reef tank that is color-neutral, so your camera will have a hard time setting a reliable white balance automatically. More importantly, reef tanks (and aquariums in general) frequently use lights that are unusually high in color temperature (such as 10, 14, and 20,000 K), and if your camera is set at standard daylight settings, your photos will come out very blue.


    Exposure: 1/350th sec at f4.0 . The depth of field at this distance is so shallow that many of the "tentacles" are in focus at the base but out of focus at the tip. (Lens: Nikon 105mm Micro)

    If you happen to know the color temperature of the bulbs (and only one color temperature is being used), you can manually set the color temperature in your camera by number, assuming your camera can be set to 10,000 and higher (mine does not go beyond 10,000). Consult your manual if you don't know how to do it already.

    More reliably, most cameras allow you to use a "preset" mode to set the color temperature. By this method, you'll take an exposure off of something that should be neutral, and your camera will use that shot to determine the white balance. What I've done is this: tape up a piece of white diffusion cloth (or a piece of lightweight printer paper) onto the center of the aquarium glass (on the outside). Turn off the lights in the room so that the only light that is on the paper is coming from the aquarium lights (wait until night if necessary). The cloth/paper should be glowing with the aquarium light. Fill your camera's frame with that piece of paper (it doesn't need to be in focus) and take your test exposure. Check your manual if necessary, there will undoubtedly be a section that explains this process in greater depth with your particular camera model. One that is done, you should be all set for the rest of the shoot.

    2. One Type of Light: ...at a time. If the tank is lit by multiple types of lights (ie, Metal Halide AND fluorescent) turn off all of the lights but one type. This includes FLASH! Fluorescent lights do not penetrate deep water as well as MH, so you'll end up slightly different colored light from the top of the tank to the bottom. Your eyes probably won't pick it up, but your camera will. Experiment with different types, though. Some creatures will fluoresce under certain lights and give you more vivid photos.

    3. RAW: Shoot in RAW format so that color temperature problems can be fixed later with ease and accuracy. You should always be shooting in RAW mode anyway, if you can, for a variety of other reasons.

    4. Re-Set: If the lighting setup changes while you're shooting, re-set the white balance. This means that if you change from MH to fluorescent or flash, you must change the white balance (or you'll pay for it later by manually doing it in Photoshop).

    5. Right Angles: Shoot with your lens pointing perpendicular to the plane of the glass to reduce distortion from the glass and water.

    6. Reduce Water Movement: Turn off pumps and filters to keep corals from swaying in the current unless you're going to be using strobes.

    7. No On-Camera Flash: On-camera flash will rarely give you satisfactory results in any situation, but it's especially problematic when you're shooting through glass. In most cases, the flash will reflect off of the glass and produce ugly glare and reduce shadow detail.

    Since I used available light in this shot, I was able to get contrast between the brighter arms of the anemone and the rich shadows (that would have been filled by on-camera flash)

    8. Reduce Glare: Turn off room lights, close curtains and blinds. Shoot with your lens as close to the glass as possible to minimize glare / reflections, or tape up a black cloth to use as a hood, with the top of the cloth attached to the top edge of the tank, and the rest hanging free so that the camera can be held underneath.

    Three Approaches to Aquarium Photography

    There are three general strategies for getting sharp photos with good colors, each of which has its own set of strengths and weaknesses. These are: shooting with flash only, shooting with high speed equipment with no flash, and shooting with low speed equipment with no flash.


    A photo taken with normal speed equipment can give nice results too, especially if you don't get too close to your subject. (Exp: 1/125th sec. f3.5)

    Shooting With Flash


    1. Set the camera's white balance to match your flash's temperature. Most cameras have a “Flash” white balance setting that will work fine. Turn off the tank lights.

    2. Place the flash so that it is shooting down from the top of the tank, or if you have multiple flashes, from the top and sides. The brightest light should be the top light, with others acting only as fill. I usually use Radiopoppers or PocketWizards to control the flashes, but cheap wireless flash triggers can be found on Ebay for less than $20 that will work fine for this type of situation.

    3. If your flash and camera are capable of iTTL metering, use it. Otherwise, manually set the exposure and check your photos frequently, since light intensity drops quickly under water and will make dramatic changes in light levels.

    The benefit of shooting with flash is that it gives you accurate color and will give you excellent sharpness, since the duration of the flash will become your effective shutter speed, and flash duration is generally between 1/1000th and 1/10,000th of a second. With bright flashes, you can also use a smaller aperture and get greater apparent focus (depth of field) in your photos.

    The drawbacks are that your corals will not fluoresce under the light of the flash, so you'll only be getting typical reflected light. And, of course, not everybody has powerful flash equipment.

    Shooting With High Speed Equipment

    Exposure: 1/1000th sec f2. This shutter speed should have precluded the possibility of camera shake, but nothing in the shot was truly sharp. The wide aperture coupled with the distortion from the water and glass was probably the cause. (Lens: Nikon 50mm f1.4)

    1. Start with a lens that has a large maximum aperture value, at least f2.8. If available, use f2, f1.4 or faster (smaller number = larger aperture).

    2. Set your ISO to the fastest speed that gives you quality results. This may be 400, 800, or with newer cameras, 1600 or faster.

    3. Set the camera on Aperture Priority (Av) mode and set the aperture to its widest setting and let the camera choose the shutter speed. This will give you the fastest shutter speeds possible with the available light, and thus, give you the sharpest photos.

    4. With sufficiently high speed equipment, you don't need a tripod. The benefit of this method is that you get pretty good sharpness and you also get the benefit of
    specialized lighting on your corals.

    The downside is that you'll get more digital noise from the higher ISO setting (like film grain), and you'll also get a very shallow depth of field. This means that if you focus on something in the foreground, your background will quickly go out of focus.

    In my experience, unless you can reliably shoot at 1/500th sec. or faster, you'll still get blurry images if you're shooting extremely close up.

    Shooting With Standard Equipment

    1. Set your camera on a tripod and use a cable release. Set your ISO to 200 (400 on newer cameras) or slower so that digital noise is not a concern.

    2. Make sure that the white balance is set as accurately as possible.

    3. Turn on your camera's auto-bracketing feature. This will provide over and under exposures, which may produce better results or can be combined later with HDR software.

    4. Set your camera to aperture priority mode and set the aperfure to f8, f11 or higher.

    The benefit of working this way is that you can get good colors, low noise, and strong depth of field, while also getting the benefits of your specialized lighting. The major drawback is that it uses slow shutter speeds, so if there is any movement in the tank, the subject can get blurred. If you're photographing something that is stationary, this is the best technique, but its no good for fish or invertebrates that move or drift with the current.


    A little further away from the subject, the depth of field appears deeper... but not much. (Exp: 1/750th sec. f2)


    In Practice


    In this case, the shallow depth of field was useful in focusing attention on the coral in the center. (exposure: 1/750th sec. at f2, Lens: Nikon 50mm f1.4)

    This was one circumstance in which having the monitor on the back of a digital camera was probably more of a hindrance than a help. I began this shoot by setting up a monolight, shooting down from the top of the tank with a Radiopopper to trigger it. When I started shooting, though, I found that with my 50mm f1.4 lens I was able to get 1/1000th sec. or faster in the top half of the tank under the metal-halide lights, so I set the white balance and started shooting hand held and from a tripod with available light.

    After I'd spent about an hour and shot a few hundred photos covering the entire tank, I decided that I'd probably done the job and I called it quits. When I took a look at the photos on my computer screen, though, I found that there was a very low proportion of sharp photos. Photos that had appeared to be sharp on the back of my camera were actually slightly blurry... but blurry enough not to be usable.

    My first reaction was that my shutter speeds had dropped down too low and I was getting blur from camera shake, since there was really nothing in the image that was sharp. Then I checked the meta-data, and found that many of them had been shot at between 1/500th and 1/1000th sec, and I started to question the possibility of camera shake. I decided in the end that the problem was probably a combination of 1) a very shallow depth of field with 2) distortion from the angle of the glass and 3) algae on the glass.

    Since I wasn't able to turn off the pumps and blowers, using a tripod and slower shutter speed to get greater depth of field was out of the question for most of the shots that I was looking for. In some cases, I could have stopped down the aperture 2 stops and still been able to stop the motion, but in most cases 1 stop was about it.


    Another example of depth of field that is too shallow. Even though the body of the fish is almost parallel with the plane of focus, the face and pectoral fin are in focus, but the tail end is not. (exp: 1/350th sec. f2)

    My recent experiments with tripod mounted photography with standard equipment have produced mixed results. Even at 1/30th of a second (with no pumps turned on), I wasn’t able to get completely tack sharp photos of soft polyps, even those with relatively rigid parts.



    I take this to indicate that in order to get nicely sharp photos (at least when shooting this close), a moderately fast shutter speed is still necessary for anything that isn't absolutely rigid. I’d try 1/60th of a second first, and take lots of photos to increase the likelihood of getting one with minimal movement. This will necessitate either an increase in ISO (and digital noise) or aperture (and loss of depth of field). I found that at around 1/45 sec. I could get reasonably sharp photos on occasion, and at ISO 400, I could get enough depth of field to get my subject’s main features if I wasn’t too close, as was the case with the blue legged hermit crab above.

    So, what would have been the best solution? Probably the best way to go would have been to use the flashes that I had brought with me. I had at least 600WS of power, which would have easily done the job. I took a test shot with only one of the heads firing and had a correct exposure at the bottom of the tank at f16 (ISO200). Needless to say, towards the top of the tank I'd have had to stop down to f22, or further unless I powered down the strobe. This would have provided a tremendous gain in depth of field, and at half power, would have given me much better motion-stopping power.

    Shot with flash only at 1/180th sec. @ f16, ISO 200.

    With some more recent experimentation, I've found that using flash has helped quite a bit in some regards, but wasn't quite the magic bullet that I’d hope for either. I did get consistent (and easy) color balance and much better depth of field, certainly. For the photo of the green thing above, I shot at f16 with my flash on 1/4 power, and could easily have gone up to f22, but I know that my lenses are not nearly as sharp at such small apertures (and they show more dust on my sensor!). That said, I thought that I would be able to shoot with my camera hand held. While I got decent results much of the time, especially when taking wider shots, at true macro distances I did get some motion blur and a tripod would have produced noticeably sharper photos.



    Another thing that I discovered was that the transmission of the light through the water and glass didn't just produce overall distortion, it produced chromatic aberration. In many shots, I got pink or green fringing, even in the center of the frame. If you know to look for it, this can be corrected in Adobe Camera Raw without too much trouble.

    I hope that this helps you in your next attempt to photograph your reef tank! Good luck, and let me know if you have any tips of your own to share.


    Matthew Gore is a wedding and commercial photographer working in the greater Seattle area. He also has nearly 15 years of experience with Photoshop, and writes a photography blog called "Light and Matter" which houses a variety of informational articles and video tutorials that are not reef-tank related.
    Comments 12 Comments
    1. Davo's Avatar
      Davo -
      Awesome, thanks for sharing tips!
      I've been into photography for many years, but I have to admit, getting those stellar shots of my reef are by far the most challenging.
    1. melev's Avatar
      melev -
      Very nice write up. The idea of a black cloth taped to the top edge of the tank was a great idea to kill those annoying reflections.
    1. Tumbleweed's Avatar
      Tumbleweed -
      Very informative. Thanks.
    1. San Juan's Avatar
      San Juan -
      Awesome pictures and tips!
      Now, only if I had a better camera with a micro lens
    1. ReefMatt's Avatar
      ReefMatt -
      Thanks I'll check back here now and then, in case anyone has any questions, but feel free to send me a private message if your question has gone unanswered for a while, since that will give me an email notification.

      - Matthew
    1. kudora's Avatar
      kudora -
      thank you for the article, i have bookmarked it and will reread it many times i am sure
    1. Mits's Avatar
      Mits -
      Any tips for those of us with basic point and shoot cameras?
    1. ReefMatt's Avatar
      ReefMatt -
      @Mits:

      Actually, a lot of the "General Tips" are the same: you can set your white balance on most point-and-shoots these days, and some of them even have RAW. Some point and shoots (I'm thinking of some of the Canon models) have excellent sensors... basically the same sensor as the DSLRs but in a smaller body, so with a higher ISO setting (with the understanding that you'll get some digital noise), you can sometimes get away with the "High Speed" equipment method that I described.

      The problem with trying to give advice for point and shoots is that there's soooo much variation. The Canon Powershot G10, for example, has a hot shoe for using external flash equipment, and full manual control, so you can use big, high powered flashes with it if you know what you're doing. Some point and shoots are worthless pieces of junk and aren't going to give you good pictures no matter what you do.

      So, when in doubt:

      1. Do whatever you can to increase the amount of light that won't increase glare off the glass. If you have halogen work lights in the garage, fire them up and point them down from the top (unless it will be bad for your tank... I don't know).
      2. Use a tripod and cable release or self-timer. That way, if your picture isn't sharp, you know that it's because your subject was moving, not your camera.

      Good luck!

      - Matthew
    1. Alaska_Phil's Avatar
      Alaska_Phil -
      Mitts
      I used a lot of the tips above with my Nikon 220S pocket camera and got some pretty decent results, nothing compared to Matthew's of course, but very acceptable for the equipment.

      The paper on the glass trick to set the white ballance worked great! Before, trying to set the white ballance to "daylight" produced blan colorless photos and trying to manually set it against the white sand produced fluorescent artificial looking color. Now I'm getting photo's that actually look like what's in the tank.

      I also got my best results using an ISO setting of 400 without too much noise. I didn't have a tripod, but braced my hands against the glass for support and managed to get decent macro shots without blurring.

      I'll try and post some of the photos later tonight.

      I doubt a shop light would have much effect compared to the high intensity lights we typically have over our reefs.
    1. Gomojoe's Avatar
      Gomojoe -
      Nice write up! What do you edit your RAW images with?
    1. ReefMatt's Avatar
      ReefMatt -
      @Phil : I was assuming that there wouldn't be anything particularly dangerous about using them, but don't want to get myself into trouble. I know that sometimes dramatic shifts in color temperature or intensity of light can cause bleaching, and I'd hate to be the cause.I didn't mean fluorescent shop lights.... I actually meant those 500 or 1000W halogen work lights (for outdoor use) and figured they might be bright enough to worry about. I bought a pair at harbor freight for $25 or so for a project once. The light color would not mix well with other HID lights in use in a tank, though.

      @Gomojoe: I use Adobe Camera RAW, usually, and then Photoshop. Of course, Adobe just released Photoshop CS5, with Camera Raw 6, which has some seriously improved noise reduction and sharpening, among other things, but I'm just starting to get comfortable with it.

      - Matthew Gore
    1. kaylabxb's Avatar
      kaylabxb -
      Thanks for the article. Bookmarked.