View RSS Feed

melev

Let there be (more) light...

Rating: 7 votes, 5.00 average.
Last year, I posted about the upgrade from single ended metal halides to TwinArc bulbs. I used the same reflectors and ballasts, but could now have 20,000K lighting for a few hours and 10,000K lighting for a few hours, daily. The best of both worlds, right? http://www.reefaddicts.com/entry.php...l-halide-bulbs

10 months later, I knew it was getting close to the time I needed to get new bulbs, and I was really debating what to go with: upgrade to all 400w bulbs and ballasts, or downgrade the middle to 250w to match the outer bulbs and ballasts. Part of making that decision was based on how the corals are doing, and partly on the PAR measurements I'd taken. When you look at the staghorn coral that is essentially under the 400w bulb, it's bursting with growth, yet the right side has less growth because it's in a semi-shaded spot between pendants, and the light it gets is from a 250w bulb. The LPS on the Bommie section (right end of the reef) seem healthy and full, but haven't really attempted to grow upwards much at all, so it makes me think more light would do them good. The entire backside of the reef gets less light than the front because of the orientation of the pendants themselves, specifically in relation to the sockets that each bulb screws into. Turning those pendants could shift where the light shines, and I may try that change as well with some more extensive measurements.

So here are some pictures of the conversion over the weekend. The first part was taking down the 250w bulb, socket and matching ballast.

Name:  light-upgrade.jpg
Views: 705
Size:  183.1 KB


The new ballast is from Reefbrite, designed for their TwinArc bulbs. It's a 400w ballast. The Icecap ballast it is replacing is over 10 years old.

Name:  ballast-comparison.jpg
Views: 739
Size:  202.8 KB


The 250w bulb looks pretty much the same as the 400w bulb. The arc appears be a little smaller internally. The new bulb is screwed into the socket in this picture.

Name:  bulb-comparison.jpg
Views: 643
Size:  216.9 KB


The end of the cord from the bulb is three wires. Usually I don't worry about the ground wire, since the bulb only uses the white and black to power up.

Name:  old-wires.jpg
Views: 651
Size:  175.8 KB


The new ballast has this connnector, so I had to cut it off to connect it to my lights.

Name:  new-ballast-cord-end.jpg
Views: 666
Size:  130.9 KB


Ready to go.

Name:  new-ballast-cord-end2.jpg
Views: 714
Size:  141.1 KB


I use these water resistant wire nuts. They contain some type of gel internally, and are generally safer around moisture.

Name:  new-ballast-wired.jpg
Views: 639
Size:  157.1 KB


The new ballasts up on the light rack.

Name:  new-ballasts-on-rack.jpg
Views: 638
Size:  170.4 KB


Here's the end result. 10,000K lighting.

Name:  10k-800px.jpg
Views: 629
Size:  169.4 KB


Turn them off and on again, 20,000K lighting.

Name:  20k-800px.jpg
Views: 765
Size:  165.7 KB


To the naked eye, I could see how much brighter the tank is. I did some initial PAR measurements, which I blogged about on Melev's Reef: http://melevsreef.com/blog/comparing...bulbs-06152014

I'll be doing some more measurements in the next week, and am reducing the total lighting period significantly to avoid burning the corals with the sudden intense PAR from the 400w bulbs. The middle of the reef should essentially be unaffected although a new bulb does put out more light than one that is 10 months old.

Name:  Screen Shot 2014-06-16 at 2.57.46 AM.jpg
Views: 539
Size:  21.1 KB


The VHOs were replaced today as well. All new lights across the reef as of now.

Submit "Let there be (more) light..." to Digg Submit "Let there be (more) light..." to del.icio.us Submit "Let there be (more) light..." to StumbleUpon Submit "Let there be (more) light..." to Google

Updated 06-16-2014 at 02:58 AM by melev

Categories
Lighting

Comments

  1. evoXmr's Avatar
    I think it looks better now that they are all the same Wattage! Your tank is looking great Marc!
  2. melev's Avatar
    I agree. Thanks!