View RSS Feed

melev

That's a first

Rate this Entry
About six months ago, I switched from the Milwaukee pH controller to the Reef Fanatic Micro pH controller. First thing I discovered was that their pH probe was a smaller diameter and required me to MacGyver a way to keep it installed in the calcium reactor.

Lately, my back pain has been so bad that I've been ignoring my reef to the point I didn't even clean the glass on the 400g and the 60g for days at a time. As the brown film amassed, I just let it go. I still checked on the calcium reactor's effluent, fed the fish and made sure the tank had more water to replace evaporation.

Starting to see some corals acting up, I did get some testing done and cleaned the glass. Alkalinity was low, like 6 dKH. I buffered that parameter up with baked baking soda (about 7 heaping teaspoons in a 12 oz cup of RO water), trickling it into the system each day for the past three days to make up for the difference. The CO2 tank was still full, but the calcium reactor needed more media. Last night I added more media.

Name:  reactor-refilled.jpg
Views: 389
Size:  181.7 KB


However, I noticed that the blinking light on the CO2's regulator wasn't coming on, and the pH controller was reading 8.35 instead of some number closer to 7.0! Not good at all. First thing I checked was the DC power supply to the CO2's regulator, and even swapped it out with another power supply but no luck. Then I looked at the Micro pH controller more closely and discovered that it had lost its programming. Fortunately the packrat that I am, I still had the box and instructions within arm's length and referred to those directions to re-learn how to install the set points. It was reset to 0.00 somehow, instead of the target 7.00 with a .02 differential.

Name:  reactor-micro-ph.jpg
Views: 357
Size:  211.7 KB


Reprogramming that set point was a little annoying as I had to hold down the button for a decent duration as it moved up from 0.00 all the way up to 7.00, but at least it is set now. The next thing I did was open the valve wide open on the Aquarium Plants regulator to add over 10 bubbles per second to get the pH to drop fast in the calcium reactor. This took about 10-15 minutes until it stabilized at 7.01. I added another cup of buffer to the reef, reset the bubble count to 2bps and called it a night.

Name:  reactor-co2-gauges.jpg
Views: 340
Size:  203.3 KB


Today's test shows Alkalinity at 8 dKH - where I prefer it to be. The reading on the pH controller is 7.05 and CO2 is being added as needed. It looks like I caught this in time before serious loss occurred.

I have no idea how the pH controller can lose its programming like this. I've never seen anything like that happen before, but I will be more vigilant checking the display to make sure the general number is close to my desired setpoint instead of only checking the CO2 tank and reactor's effluent rate.

Submit "That's a first" to Digg Submit "That's a first" to del.icio.us Submit "That's a first" to StumbleUpon Submit "That's a first" to Google

Categories
Equipment

Comments

  1. gettareef's Avatar
    Weird...Whew! Close one (hope this doesnt become a regulag thing, esp if it happens when youre out of town). Sorry to hear about your back pain; hope your surgery goes well
  2. Peiloy's Avatar
    Just out of curiosity, why not use the Apex instead of the pH controller to do the same function. Ive been doing it for years without a problem and I have alarms set up for high and low PH in the reactor set in the Apex. So if my AP regulator goes wonky for whatever reason or if I am low on CO2 I will be emailed. Another thought is if you want to keep the pH controller as redundancy you could drip your effluent into a cup and stick the pH probe from the Apex in there so that you at least have the pH logging and can set up alarms for high/low pH levels.
  3. melev's Avatar
    I got a response from Reef Fanatic. Turns out this controller loses its programming if it isn't plugged into a UPS. So I'll have to move the cord to the UPS that the Apex currently uses to avoid this problem from happening again.